Multi-purpose grease for vario-seatposts, suspension forks and shocks.The special additives help to prevent corrosion when used regularly and keeps seals and wipers supple.We use this grease in our production, and it is suitable for all BikeYoke seat posts.Quantity:30ml (sufficient for about 5 services)Scope of delivery:1x BikeYoke Dropper Goo
BikeYoke Sanguine is designed specifically for the use in BikeYoke seat posts.The formula reduces friction, ensuring fast action with minimal drag even in low winter temperatures below 0°C.Special additives help keep your post's o-rings and seals smooth and reduce wear.Suitable for all BikeYoke droppers.Quantity:250ml (sufficient for several complete services of your BikeYoke support)Scope of delivery:1x BikeYoke Sanguine
Replacement foam rings and bottom out bumper for your BikeYoke dropper post.The foam ring in the lower tube of your BikeYoke dropper post is a crucial component, that prevents water and dirt from entering your post too easily.Keep it dry and clean at all times, so your post can breathe and replace if needed.includes:4x foam ring25 mm:REVIVE 27228 mm:REVIVE 3.0REVIVE MAX 3.0DIVINE SLDIVINE SL Rascal31 mm:REVIVE 1.0/2.0DIVINE34 mm:REVIVE MAX 1.0/2.0
Service kit for readjusting the lateral play of our dropper seatposts and renewing the wiper as part of the 100-hour service.ATTENTION!!!There are three different kits for the REVIVE and DIVINE, depending on the model year/revision. The kits are not compatible with each other!Be sure to select the correct service kit for your post!Note on foam rings: 28mm is to be used for all 3.0 generation foot assemblies 31mm is to be used for all pre-3.0 generation foot assemblies
Note:Our Service Kit Guide will help you to identify the correct kit for your seatpost. You will find the serial number on the lower tube of the seat post.Scope of delivery:1x wiper6x glide pin1x lower bushing1x foam ring 28mm1x foam ring 31mm1x circlip R12
Note:During factory assembly upper bushings in every single REVIVE, REVIVE MAX and DIVINE are precision-calibrated with a special tool. Our official service centers have access to these tools. Replacement at home can (but does not have to) lead to increased friction between tubes. To achieve best results and proper fit, we therefore recommend replacing the upper bushing in one of the mentioned posts only at our service centres. compatibilty:dimensions in mm ID x OD x H22x24x7:REVIVE 27225x27x7:REVIVE 1.0 30.9/31.6REVIVE 2.0 30.9/31.6REVIVE 3.0 30.9/31.6DIVINE SL und Rascal (neue Generationen)*25x28x7:DIVINE SL and Rascal (older generations)*28x30x7:REVIVE MAX 1.0 34.9REVIVE MAX 2.0 34.9REVIVE MAX 3.0 34.9 * The DIVINE SL and Rascal can contain two bushing sizes, depending on the post generation. Earlier models use 25x28x7mm busihngs, newer ones use 25x27x7mm bushings.You can identify the correct version for your post via serial number and our service kit guide. The serial number can be found on the lower tube of the seatpost.includes:1x upper DU-bushing
Includes all hydraulic seals to perform a complete cartridge rebuild of your BikeYoke dropper post.compatible with:REVIVE / REVIVE 2.0Note:Please pay attention to the video description. You can find it under the installation tab.
New friction-optimized premium cable set for cable-operated seatposts.The new cable-wire combination with a 3 mm outer housing and a 0.9 mm wire allows for easier routing through the frame. Moreover, the significantly lower friction between the outer housing and the inner cable ensures even smoother actuation of the seatpost, which is particularly beneficial in case of tight loops/radii (e.g. when routing the cable through the headset).The Premium seat post cable set can be used with all standard cable-operated seatposts.Note: The cable set is not suitable for use as a shift cable.Includes:1x Inner cable, stainless steel, polished and coated, 1800mm (diameter 0.9 mm) 1x Outer housing 1600mm (diameter 3 mm) 2x End cap for outer housing 1x Crimp end cap for inner cable Fits: REVIVE / REVIVE 2.0 / REVIVE 3.0REVIVE MAX / REVIVE MAX 2.0 / REVIVE MAX 3.0DIVINE
Scope of delivery: 4x spacers for travel adjustmentFits with:REVIVEREVIVE MAXDIVINEDIVINE SL / RascalNote:The video under the Installation tab shows the installation process on a DIVINE. The REVIVE has a slightly different internal structure, but the installation is performed in the same way: Spacers must be clipped onto the shaft between the piston and seal head.'When using more than 4 spacers, oil volumes need to be reduced as following:5 spacers = -0.5cc6 spacers = -1.0cc7 spacers = -1.5cc8 spacers = -2cc...Generally, we recommend opting for the next shortest drop length rather than reducing the travel by more than 20mm.
Seatpost cable set for Bikeyoke seatposts with foot unit.Scope of delivery:1x inner cable, stainless steel, polished, 1700mm (1.1mm diameter)1x outer cable 1500mm (4.2mm diameter)2x housing endcap1x inner cable cable crimpFits: REVIVE / REVIVE 2.0REVIVE MAXDIVINETipp:For our posts, we use standard shift cables and housings, which allow easy supply and exchange.Mind, that there are 1.1mm cables (e.g. SRAM) and 1.2mm cables (e.g. Shimano), which will both work with our posts, but require matching housings.Attenton:Does not fit DIVINE SL, DIVINE SL Rascal und REVIVE 272
The upper saddle clamp 3.0 is compatible with all BikeYoke REVIVE seatposts.The saddle clamps 3.0 reduce the stack height of the seatpost by 5 mm compared to the previous generation.NOTE: The upper saddle clamp 3.0 can only be used in combination with the lower saddle clamp 3.0.
includes:1x upper seat clamp 3.0compatible with:REVIVE / 2.0 / 3.0REVIVE MAX / 2.0 / 3.0REVIVE 272
The lower saddle clamp 3.0 is compatible with all BikeYoke REVIVE seatposts.The saddle clamps 3.0 reduce the stack height of the seatpost by 5 mm compared to the previous generation.NOTE: The lower saddle clamp 3.0 can only be used in combination with the upper saddle clamp 3.0. includes:1x lower seat clamp 3.0compatible with:REVIVE / 2.0 / 3.0REVIVE MAX / 2.0 / 3.0REVIVE 272
The upper seat clamp is compatible with all BikeYoke seat posts.Version 2.0 is the latest version.Scope of delivery:1x upper seat clampFits with:REVIVE / REVIVE 2.0REVIVE MAXREVIVE 272DIVINE SLDIVINE SL RASCAL
Saddle clamp bolt version 2.0 with integrated spherical washer.Our posts use two different lengths*:37mm for the front bolt40mm for the rear boltScope of delivery1x saddle clamp boltCompatible with:REVIVE / REVIVE 2.0REVIVE MAXDIVINEDIVINE SLDIVINE SL RASCAL*measures include head
Titanium bolt set for the saddle clamp.The bolts and barrel nuts are compatible with all BikeYoke models.This set is not composed of standard parts but is custom-made according to our drawings and specifications.Both the bolts and the barrel nuts are CNC-machined from the high-strength titanium alloy Ti-6Al-4V and save almost half the weight of the original stainless-steel set.Fits: REVIVEREVIVE 2.0REVIVE MAXREVIVE 272DIVINEDIVINE SLDIVINE SL RascalOne set includes:2x Ti-6Al-4V bolt2x Ti-6Al-4V barrel nut
Attaches to your Reset-Hex-Slot instead of the 4mm Allen-Key, secured by an o-ring (included).No more need to grab your 4mm Allen-Key.Insert the Quick-Reset-Lever carefully and completely into the 4mm Allen key slot to not damage the o-ring and to make sure it is secured properly.You can easily engage it with a pull of your finger.Scope of delivery:1x Quick-Reset-LeverFits:REVIVE/REVIVE 2.0REVIVE MAXREVIVE 272
NOTE: *When used as an upgrade on REVIVE 1.0, REVIVE 2.0 or DIVINE, the new foot unit also requires the acturaotr rod 3.0 (number 34 on explosion drawing of REVIVE THREE) REVIVE 3.0 push rod.Furthermore, the actuator unit 3.0 requires the cable barrel 3.0includes: 1x foot assemblycompatible with: REVIVE 3.0REVIVE 1.0 / REVIVE 2.0 (30.9/31.6)*DIVINE (30.9/31.6)*
cable barrel for dropper seatpostThe cable barrel 3.0 does not need to be clamped and can simply be threaded onto the shifting cable and hooked in.NOTE: When using the cable barrel, it is necessary that the other end of the cable can be clamped directly to the remote of the seat postincludes:1x cable barrel 3.0compatible with: REVIVE 3.0REVIVE MAX 3.0
Cable clamp to actuate our REVIVE and DIVINE posts.Includes:1x Cable clamp body1x Set screw DIN 913 M4x5Fits:REVIVE / REVIVE 2.0REVIVE MAXDIVINE2X-RemoteTipp:This item is identical to cable clamps that are used on other posts, e.g. KS (Kindshock) LEV Integra.
€3.00*
This website uses cookies to ensure the best experience possible. More information...
